How To Fix A Craftsman Chainsaw That Won’t Start. Top Troubleshooting Tips
Share it
It is possible that your Craftsman Chainsaw has stopped working after only a few use. It could be due to a variety of reasons. It could be that the fuel is not high-quality or that the carburetor is blocked.
Our engineers have provided some tips and tricks to help you fix Craftsman’s chainsaw not starting.
Common Solutions For Craftsman Chainsaw Start Issues
Based on the research and testing of our teams, here are the most common ways to fix your CraftsmanChainsaw’s starting problems:
Fix #1: Use High-quality Fuel And The Correct Fuel Mix
Always use high-quality, fresh fuel to ensure your chainsaw runs smoothly. Fresh fuel burns well and doesn’t accumulate water in your tank. To keep the gas in its freshest state, you will need to add fuel stabilizer.
You should not keep the fuel in the tank for more than three months without using a stabilizer. You can buy ethanol-free pre-mixed fuel to help you determine the right fuel mix.
2. Clean The Fuel Filter
If your fuel filter is dirty, it may make it difficult for the chainsaw to start.
The fuel filter can be cleaned or replaced. No matter how often you use your chainsaw, you should replace the fuel filter at least once per year.
Solution #3: Clean The Air Filter
A dirty air filter can also cause problems for your chainsaw, just like a dirty fuel filter. The chainsaw could then stop working after being given gas. Worse, the air filter may cause your saw to have a shorter lifespan. After using your chainsaw for more than five hours, check the air filter.
Brushing the air filter can remove any sponginess. To prevent any damage, do not use compressed air. Use warm soapy water to clean it. Rinse it with cool water.
It is best to dry it before you put it back on your chainsaw. The filter can be replaced once a year, or as often as you need. For compatibility, its best to purchase the filter fromwho made yourchainsaw-Craftsman.
#4: Clean The Carburetor
The carburetor is a device that combines fuel and air to ignite the engine’s internal combustion. Sticky fuel can cause the carburetor to become clogged. It is difficult to start the chainsaw if the carburetor becomes blocked.
This test can be used to determine if the carburetor is causing Craftsman’s chainsaw not starting. Take out the air filter and add a tablespoon of fuel to it. Start the saw. The carburetor is likely to be the problem if the saw starts but stops immediately.
To clean small clogs, remove the fuel. Clean the carburetor. If the carburetor becomes too clogged, it may be necessary to replace it. You should ensure that you purchase the right carburetor for your chainsaw.
Fix #5: Check The Spark Plug For Damage
Spark plugs provide the spark that ignites a gas-powered chainsaw. The spark plug can’t spark the chainsaw if it isn’t working properly. Check for dirt or damage by removing the spark plug.
Also, you can find carbon buildup and burned electrodes in your spark plug. A spark plug is not something you can easily clean, unlike other parts of your chainsaw. To be able to use your chainsaw safely, it is necessary to replace the spark plug if it has any of the problems mentioned above. It can also be changed annually.
Fix #6: Replace Your Ignition Coil
The spark plug works by sending power voltage to the ignition coil. The ignition coil can become damaged from repeated use, and your chainsaw may not start. If you can’t see spark coming from the ignition coil, make sure the spark plug is clean.
An ignition coil tester can be purchased or the coil may be replaced. If the tester does not produce a spark, it is possible to replace the ignition coil.
Fix #7: Make Sure To Check The Rewind Spring For Damages
After every pull, the rewind spring retracts the starter cord. If the starter cord does not rewind after each pull, or the rewind spring breaks, the engine will not start. If this happens, you will need to replace the rewind spring.
You can check your chainsaw model to see if the rewind spring can be replaced individually or if the entire recoil starter needs to be replaced.
Conclusion
You must first identify the problem to fix Craftsman Chainsaws that won’t start. To prevent further damage, our professionals recommend that each component be kept clean. If you use your chainsaw frequently, it is still important to replace some of the parts listed above at least once per year.
